 |
LIRC libraries
LinuxInfraredRemoteControl
|
One remote as represented in the configuration file. More...
#include <ir_remote_types.h>
Public Attributes | |
| const char * | name |
| name of remote control | |
| const char * | driver |
| Name of driver for LIRCCODE cases. More... | |
| struct ir_ncode * | codes |
| int | bits |
| bits (length of code) | |
| int | flags |
| flags | |
| int | eps |
| eps (relative tolerance) | |
| unsigned int | aeps |
| detecting very short pulses is difficult with relative tolerance for some remotes, this is an absolute tolerance to solve this problem usually you can say 0 here. More... | |
| char * | dyncodes_name |
| name for unknown buttons | |
| int | dyncode |
| last received code | |
| struct ir_ncode | dyncodes [2] |
| helper structs for unknown buttons | |
| lirc_t | phead |
| lirc_t | shead |
| header | |
| lirc_t | pthree |
| lirc_t | sthree |
| 3 (only used for RC-MM) | |
| lirc_t | ptwo |
| lirc_t | stwo |
| 2 (only used for RC-MM) | |
| lirc_t | pone |
| lirc_t | sone |
| 1 | |
| lirc_t | pzero |
| lirc_t | szero |
| 0 | |
| lirc_t | plead |
| leading pulse | |
| lirc_t | ptrail |
| trailing pulse | |
| lirc_t | pfoot |
| lirc_t | sfoot |
| foot | |
| lirc_t | prepeat |
| lirc_t | srepeat |
| indicate repeating | |
| int | pre_data_bits |
| length of pre_data | |
| ir_code | pre_data |
| data which the remote sends before actual keycode | |
| int | post_data_bits |
| length of post_data | |
| ir_code | post_data |
| data which the remote sends after actual keycode | |
| lirc_t | pre_p |
| lirc_t | pre_s |
| signal between pre_data and keycode | |
| lirc_t | post_p |
| lirc_t | post_s |
| signal between keycode and post_code | |
| uint32_t | gap |
| time between signals in usecs | |
| uint32_t | gap2 |
| time between signals in usecs | |
| uint32_t | repeat_gap |
| time between two repeat codes if different from gap | |
| int | toggle_bit |
| obsolete | |
| ir_code | toggle_bit_mask |
| previously only one bit called toggle_bit | |
| int | suppress_repeat |
| suppress unwanted repeats | |
| int | min_repeat |
| code is repeated at least x times code sent once -> min_repeat=0 | |
| unsigned int | min_code_repeat |
| meaningful only if remote sends a repeat code: in this case this value indicates how often the real code is repeated before the repeat code is being sent | |
| unsigned int | freq |
| modulation frequency | |
| unsigned int | duty_cycle |
| 0<duty cycle<=100 default: 50 | |
| ir_code | toggle_mask |
| Sharp (?) error detection scheme. | |
| ir_code | rc6_mask |
| RC-6 doubles signal length of some bits. | |
| unsigned int | baud |
| can be overridden by [p|s]zero, [p|s]one | |
| unsigned int | bits_in_byte |
| default: 8 | |
| unsigned int | parity |
| currently unsupported | |
| unsigned int | stop_bits |
| mapping: 1->2 1.5->3 2->4 | |
| ir_code | ignore_mask |
| mask defines which bits can be ignored when matching a code | |
| ir_code | repeat_mask |
| mask defines which bits are inverted for repeats | |
| ir_code | toggle_bit_mask_state |
| int | toggle_mask_state |
| int | repeat_countdown |
| struct ir_ncode * | last_code |
| code received or sent last | |
| struct ir_ncode * | toggle_code |
| toggle code received or sent last | |
| int | reps |
| struct timeval | last_send |
| time last_code was received or sent | |
| lirc_t | min_remaining_gap |
| remember gap for CONST_LENGTH remotes | |
| lirc_t | max_remaining_gap |
| gap range | |
| lirc_t | min_total_signal_length |
| how long is the shortest signal including gap | |
| lirc_t | max_total_signal_length |
| how long is the longest signal including gap | |
| lirc_t | min_gap_length |
| how long is the shortest gap | |
| lirc_t | max_gap_length |
| how long is the longest gap | |
| lirc_t | min_pulse_length |
| lirc_t | max_pulse_length |
| lirc_t | min_space_length |
| lirc_t | max_space_length |
| int | release_detected |
| set by release generator | |
| int | manual_sort |
| If set in any remote, disables automatic sorting. More... | |
| struct ir_remote * | next |
One remote as represented in the configuration file.
Definition at line 155 of file ir_remote_types.h.
| unsigned int ir_remote::aeps |
detecting very short pulses is difficult with relative tolerance for some remotes, this is an absolute tolerance to solve this problem usually you can say 0 here.
Definition at line 162 of file ir_remote_types.h.
| const char* ir_remote::driver |
Name of driver for LIRCCODE cases.
Definition at line 157 of file ir_remote_types.h.
| int ir_remote::manual_sort |
If set in any remote, disables automatic sorting.
Definition at line 242 of file ir_remote_types.h.
1.8.8 
